Rane CP 64 (1999-2004 version) User Manual download pdf

Manual-1

OPERATORS MANUAL CP 64

COMMERCIAL PROCESSOR

QUICK START

If you were the type that cheated on school book reports by just skimming through the reading assignments, then this

section is for you! It gives you not quite enough information to really know what you’re doing. But, if you follow the

recommended set up procedure, you should get at least a “B.”

Keep the amplifiers and the CP 64 turned off until all connections are made.

INTERNAL SETTINGS: Access to the following internal controls requires removal of the top cover. All internal

settings should be complete before you install the CP 64. The factory default settings work for many applications. How-

ever, you may need to change one or more for your system. See the INTERNAL ADJUSTMENTS description on page

Manual-8 for more details

• Each Page Input has a 15 volt Phantom Power switch. The default is off.

• The Page Priority switch assigns priority override to Page 1, Page 2 or NO (none). The default is Page 1. If a Page has

priority, it overrides the non-priority Page in the Zone(s) it is assigned. The NO priority setting allows the Pagers to mix.

• Each Page Input may sum with the Program Pre- or Post-VCA. When set to Pre-VCA, Zone Level, EQ and Limiter

circuits act upon the Page. When summed Post-VCA, the Page is not influenced by Zone Level, EQ or Limiter circuits.

The default is Pre-VCA.

• The Zone 1 Stereo/Mono switch default is Stereo.

• There are two internal trim controls for the Program Priority detector. The Program Priority Threshold trim has a range

of -∞ to -35 dBu with a default of -50 dBu. The Program Priority Release Time has a range of 2 to 20 seconds. The

default is 12 seconds.

PAGE INPUTS: Connect Page Inputs to the Euroblock on the rear panel and select the appropriate MIC or LINE

switch position for each. First, set the gain with the Page TRIM control, then set the Page DETECT THRESHOLD and

finally the Page Zone LEVEL.

PR 2 REMOTE: If you use the optional PR 2 remote (sold separately), wire it to the rear RMT ZONE ASSIGN

Euroblock as indicated. If you require remote control but do not wish to use a PR 2, any simple switch closure to GND will

work. These inputs are also TTL compatible (0 to 5 VDC). See wiring details on pages Manual 9-10.

PROGRAM INPUTS: Connect Program sources to the RCA PROGRAM INPUTS (L1, L2, L3 & P.) If you have a

priority program, like a jukebox, connect it to the PRIORITY Input. The Program PRIORITY ASSIGN switch assigns

priority override to Off, Zone 1, Zone 2, or Both. In the Zone(s) that it is assigned, the priority program is automatically

selected when signal is detected.

EXPAND OUTPUTS: Wire the EXPAND OUTPUT Euroblock for each Zone as required. These are cross-coupled

line drivers and may be used balanced or unbalanced. Each Expand Output can be Page-only, Program-only or Zone

signal. The Zone source will not include the Page if the Page is summed Post-VCA. Page is always available from the Page

source.

ZONE OUTPUTS: Wire the two ZONE OUT Euroblocks as required. These are cross-coupled line drivers and may

be used balanced or unbalanced. Set the LIMIT threshold as required.

ZR 1 REMOTE: You may use one or two ZR 1 Remotes with each CP 64. If you use the optional ZR 1 remote (sold

separately), wire it to the rear REMOTES Euroblock as indicated. If a ZR 1 remote is not used, any simple switch closure

to GND will work for the D0 and D1 pins. These pins are TTL compatible (0 to 5 VDC). The logic is inverse Gray Code.

Any ground referenced 5 volt DC control may be used as the input to V

or V

. Do not ground the Vr

or Vr

pins. See

wiring details on pages Manual 9-10.

The CP 64 is very versatile. While this makes a large number of system applications possible, it also results in complex-

ity. For this reason, it is important to use an organized approach for setup and calibration. A highly recommended setup

procedure appears on page Manual-11. By following it you will encounter fewer problems and reduce the need to increase

our collective phone bills.

WEAR PARTS: This product contains no wear parts.

1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1 - OPERATORS MANUAL CP 64

Manual-1OPERATORS MANUAL CP 64COMMERCIAL PROCESSORQUICK STARTIf you were the type that cheated on school book reports by just skimming through the re

Page 2 - CP 64 FRONT PANEL

Manual-10REMOTE MOUNTINGThe ZR 1 and PR 2 remote assemblies mount in a standardU.S. electrical box with a minimum depth of 2.25". Be sure tonote

Page 3 - CP 64 REAR PANEL

Manual-11RECOMMENDED CALIBRATION PROCEDUREThe CP 64 is a very versatile instrument. While this allows it to conform to the requirements of a large nu

Page 4 - Manual-4

Manual-12©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL (425)355-6000 FAX (425)347-7757 WEB http://www.rane.com…CP 64 Calibrati

Page 5 - Manual-5

Manual-2CP 64 FRONT PANEL햲 PAGING ZONE ASSIGN switches select the zone(s) a Page signal is sent to. The RMT position activates the rear panelRMT ZONE

Page 6 - Manual-6

Manual-3CP 64 REAR PANEL햲 CHASSIS GROUND SCREW provides a convenient earth (technical) ground connection point. The CP 64 does notground the chassis t

Page 7 - Manual-7

Manual-4SYSTEM APPLICATIONS The following applications outline four unique system configurations. It is not practical to show every possibility, but

Page 8 - INTERNAL ADJUSTMENTS

Manual-5SYSTEM 2 : SMALL MANUFACTURING / SMALL OFFICE / RETAIL STORE• If the phone system selects Zone(s), set the PAGE 1 ZONE ASSIGN to Zone 1 and

Page 9 - REMOTE INSTALLATION

Manual-6Internal Settings: Page Priority to P2 (see page Manual-8).Both P1 and P2 to Post-VCA summing.Zone 1 Mode set to Stereo.Front Panel Settings:

Page 10 - Manual-10

Manual-7SYSTEM 4: EXPAND TO OTHER CP 64s: AUTO DEALERSHIPRESTROOMSEXPAND MUSIC ON HOLDPRIORITY 3SERVICE WRITERAND PARTS ROOMZR1SERVICE BAYSDISTRIBUTED

Page 11 - Manual-11

Manual-8INTERNAL ADJUSTMENTS There are a number of controls inside the CP 64 used toconfigure the system for specific applications. Access to thesecon

Page 12 - Manual-12

Manual-9LEVEL control. Note the following:• Zone Level, EQ and Limiter circuits do not affect Pagesignals summed Post-VCA.• Zone Level, EQ and Lim

Comments to this Manuals

No comments

Rane CP 64 (1999-2004 version) User Manual

Browse online or download User Manual for Audio Rane CP 64 (1999-2004 version). Rane CP 64 (1999-2004 version) User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Audio Rane CP 64 (1999-2004 version)