Manual-3
CROSSFADER CONTOUR control: Allows adjusting the “shape” of the Crossfader response from a gentle curve for
smooth, long running fades, to the steep pitch required for top performance cut and scratch effects. See Figure 1 on page
Manual-1.
Meter and Mode switch: This peak-dBu reading meter displays one of two modes, depending on the switch position. In the
LEFT/RIGHT (out) position, the meter indicates the stereo level in the LEFT and RIGHT Main Outputs. In the CUE/PRG
(in) position, mono CUE level is displayed on the Left meter and mono PROGRAM level is displayed on the Right meter.
MASTER LEVEL fader: adjusts the level at the rear panel Main Outputs.
AUX INPUT: This stereo pair of RCA connectors is an extra line level Input which sums with the other signals before the
Master Level fader.
AUX IN LEVEL control: adjusts the level of the front panel Aux Inputs.
AUX OUTPUT: This stereo pair of RCA connectors provides an extra line level output mix. This is the same signal as the
Main Outputs, but with a separate Level control.
AUX OUT LEVEL control: adjusts the level of the front panel Aux Outputs. This control is independent of the Master
Level fader and Main Outputs.
CUE switches: Pressing in any or all of the CUE pushbuttons routes the respective Source to the Headphone and Meter Cue
sections. The adjacent yellow indicator illuminates when the switch is depressed.
HEADPHONE PAN control: adjusts the relative levels of Cue and Master signals mixed together in stereo for the head-
phones. Counterclockwise rotation increases the amount of Cue signal; clockwise rotation increases the amount of Master
signal.
HEADPHONE LEVEL control: adjusts the volume for the headphones.
HEADPHONE Output jack: This stereo ¼" TRS (Tip-Ring-Sleeve) jack accepts ¼" TRS stereo headphone plugs (do not
use mono plugs).
POWER “ON” indicator: When the yellow indicator is lit, the MM 8z is ready to go.
Fader Cleaning
With heavy use in harsh environments, the faders may
need lubrication. This treatment extends longevity and can
make used faders as good as new. The fader assembly must
be removed from the MM 8z for proper cleaning. We recom-
mend any of the following cleaning solutions:
Caig Cailube MCL 100% spray lubricant
Caig Cailube MCL 5% spray cleaner
CRC 2-26
Order CaiLube MCL
®
from:
CAIG Laboratories, Inc.
12200 Thatcher Ct.
Poway, CA 92064
Phone 619-486-8388
Fax 619-486-8398
Web http://www.caig.com
REPLACING THE ACTIVE CROSSFADER
The Crossfader may be removed without any disassembly
of the MM 8z itself, and may be performed while the unit is
operating with no interruption of the audio signal.
F 60 and F 45 Fader Kits are available from your local
retailer or the factory. The kit includes full assembly includ-
ing knobs, ribbon, and face plate.
1. Remove the two (2) outer screws attaching the crossfader
assembly to the front panel.
2. Pull the Crossfader Assembly forward and unplug the
ribbon from the connector on the bottom board.
3. Proceed with Cleaning Instructions, or install the replace-
ment assembly by reversing the above instructions.
CLEANING INSTRUCTIONS
1. Hold the fader assembly away from the mixer.
2. Position the fader at mid-travel.
3. Spray cleaner/lubricant into both ends of the fader.
4. Move the fader over its full travel back and forth a few times.
5. Shake excess fluid from the fader assembly.
6. Wipe off excess fluid.
(3 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals