Rane TTM 57SL Operator's Manual Page 9

  • Download
  • Add to my manuals
  • Print
  • Page
    / 60
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 8
Phones
The headphone output can
deliver very high volume to some
headphones. To avoid pain,
never put headphones on your
head before plugging them in. Always
start with the PHONES Level turned
down, and then turn it up to the desired
level.
Cue
This slider pans between
PGM 1 and PGM 2 in the
headphones when the
Master Cue light is off. When Master Cue
is on, this control has no effect. The cue
signals are post-EQ and pre-fader.
Master Cue
Press this switch (green light
on) to hear the Main Mix in
the headphones. When this light is off, the
Cue slider takes over.
FlexFX Loop
This stereo loop connects an
external effects processor,
post-fader. The signals coming
from the PGM 1 fader, the PGM 2 fader,
or both may be routed to the FlexFX loop.
This allows a single external effects unit to
process PGM 1 and/or PGM 2.
NOTE: This Loop is for an external
effects unit. For details on the built-in
internal effects, See “Effects” on page
41.
FlexFX switches are provided for PGM 1
and PGM 2. Pressing the FlexFX switch
lights the green indicator and sends the
signal to the external FlexFX Loop. Press
the switch again to stop sending signal to
the loop (the green indicator goes dark).
FlexFX jacks are unbalanced mono ¼" TS
(Tip/Sleeve). SEND jacks provide output
to the effects processor. RETURN jacks
provide input from the effects processor.
Effects insert devices with a single in/
out TRS jack place Send on the TIP and
Return on the RING. For this application,
you will need a “Y” cable, as shown
below.
Send signals may be used as another
auxiliary output, allowing PGM 1, PGM
2 or both to be routed to an external
source (another amp or recorder). If you
wish to disconnect your external effects
processor, it is not necessary to connect
cables from FlexFX Send to FlexFX
Return, as the TTM 57SL detects the
presence of cables, and automatically
connects the Send and Return when a
cable is not connected.
Any signal assigned to the FlexFX Loop
will be processed by any internal digital
effect assigned to the AUX BUS. This has
the advantage of allowing one of the two
internal effects to be assigned to the AUX
BUS and then assigning PGM 1 and/or
PGM 2 to the FlexFX Loop.
Aux In
This adjusts the level of the
Auxiliary Input signal. This is a
full-range control providing Off
to +6 dB gain adjustment.
Mic Level and EQ
The MIC ON switch engages
the Mic. The green indicator
is lit when the MIC is
engaged. MIC LEVEL adjusts
the Mic gain over a range of
Off to +50 dB. Set the gain
where you want it and use
the MIC ON switch to turn
the MIC on and off. The OL
indicator lights when the
signal reaches clipping. If
this lights red, turn the MIC
LEVEL down. MIC HIGH and
MIC LOW tone controls allow
you to adjust the bass and treble of the
MIC Input signal.
Output Levels
Output Level controls
are provided for MAIN,
BOOTH and AUX Outputs.
All three outputs have the
same Main Mix source.
As shown previously in
Analog Outputs (on page
Manual-3), the Main output
is a balanced output on
XLR connectors, the Booth
output is a balanced
signal on TRS connectors
and the AUX output is an
unbalanced signal on RCA connectors.
This combination of jacks allows you to
hook into other equipment regardless of
the connector type.
Headphone Cueing
The Cueing system allows users to
Pan the Cue from PGM 1 to PGM 2 or
select the Master Mix. Cueing is also
provided for the internal digital effects,
covered on page-10. Both 3.5 mm
and ¼” jacks are provided. These can
be used simultaneously, but using only
one at a time yields more power to the
headphones.
(XLR)
(TRS)
(RCA)
SEND/RETURN CABLE WIRING
1-CONDUCTOR SHIELDED CABLE
1-CONDUCTOR SHIELDED CABLE
T = SEND
R = RETURN
S = SHIELD
++SEND
RETURN
++
SHIELD SHIELD
SHIELD
RANE TTM 57SL MIXER FOR SERATO SCRATCH LIVE • OPERATOR’S MANUAL 2.4.4
9
Page view 8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 59 60

Comments to this Manuals

No comments